Product Description
Product Presentation
| CTG Series Parameter Table | |||||||||||
| Model | J7.5PMCTG | J11PMCTG | J15PMCTG | J22PMCTG | |||||||
| Rate Power | 7.5kW | 11kW | 15kW | 22kW | |||||||
| Pressure(MPa) | 0.8 | 1.0 | 0.8 | 1.0 | 1.6 | 0.8 | 1.0 | 1.6 | 0.8 | 1.0 | 1.6 |
| F.A.D(m3/min) | 1.1 | 0.9 | 1.6 | 1.4 | 1.0 | 2.6 | 2.0 | 1.5 | 3.6 | 3.0 | 2.3 |
| Drive Type | PM Motor/Direct-driven | ||||||||||
| Voltage/Frequency | AC380V-50Hz | ||||||||||
| Starting Mode | Variable Frequency | ||||||||||
| Connection | G3/4” | G3/4” | G3/4” | G1” | |||||||
| Size(LxWxH) | 1450X860X1585mm | 1850X1030X1880mm | 1850X1030X1880mm | 1850X1030X1880mm | |||||||
| Weight | 350kg | 510kg | 510kg | 560kg | |||||||
Comparison between permanent magnet motor and ordinary asynchronous motor
Compared with electrically excited motors, permanent magnet motors have the following advantages:
High efficiency
Eliminate excitation system loss, improve efficiency 5-12%, high power factor, large torque inertia ratio, stator current and stator resistance loss reduction, and rotor parameters can be measured, good control performance, motor direct drive, no speed slip, no bearing and connection transmission, efficiency increased by more than 3%, light load than the same specification asynchronous motor efficiency increased by 15-35% or so. Always efficient regardless of light load or heavy load. At present, the energy efficiency of permanent magnet motors used by Hylein has reached the national level 1 energy efficiency standards.
Low noise
Reasonable magnetic field design, magnetic density distribution, wider operating frequency range, lower operating noise. Truly constant air pressure: open loop vector control, response time < 50ms, can adjust gas production in an instant over a wide range.
Compact structure, small size, light weight, high precision and fast response
The exciting winding and the exciting power supply (magnetic pole core) are eliminated, and the structure is simple, the operation is reliable and the maintenance is convenient.
High starting torque
The starting torque and overload capacity of permanent magnet synchronous motor are 1 power level higher than that of three-phase asynchronous motor, and the ratio of the maximum starting torque to the rated torque can reach more than 3 times, while the general asynchronous motor is only 1.6 times.
Single Stage Compression
Oil cooled machine
Core Ndfeb magnetic steel, not only high temperature 180ºC, and energy efficiency level is higher than IE5. The heat loss is small and the efficiency is high under the same power.
Reliable intake valve system
Unique structural design, reliable intake valve system, do not have to worry about emergency shutdown and sudden power outage oil injection.
The oil and gas pipe of the whole machine are made of stainless steel material or imported hose, which is durable and not aging. It is sealed with thread and flat O-ring, easy to disassemble without leakage.
Rear exhaust design to suck instead of blow
Fans dissipate heat faster and make less noise. The traditional fan blows against the cooler, which has large resistance and loud noise. The back row is cooled, and the cooler is placed vertically to avoid the dust falling on the cooler from the top down, which will lead to slow blockage for a long time. This design avoids.
New oil-cooled motor
Mold forming, no welding points, no risk; Rotary oil passage circulation, small pressure difference; It’s a circular surface; Circular surface type oil passage, full oil flow, uniform cooling oil passage in the outside, easy to repair and maintenance.
Quality Upgrade Three Lightspots
Company Profile
HangZhou Hylein Energy & Environmental Technology Co., Ltd. is located in HangZhou, Pearl River Delta, known as China’s compressor production base, is a professional engaged in all kinds of screw air compressor, nitrogen machine, oxygen generator, vacuum pump, magnetic suspension compressor R & D, production and sales of manufacturing enterprises, with standard production assembly line, the introduction of Europe and North America mature and experienced technology, Focus on providing a full range of services for various industries.
We strictly follow the IS09001 quality system standards and related industry standards, and throughout the product design, procurement, manufacturing, inspection, sales and service of the entire process, we always adhere to the global procurement strategy to ensure the superior performance of each air compressor, we pay attention to the development of new products, the latest energy-saving products are providing quality services for the global industrial energy-saving cause.
In the ZheJiang -ZheJiang Railway oxygen supply system air compressor project, we overcome high altitude, ultra-low temperature, ultra-high temperature, huge dust, frequent switching power supply and other problems.
After-sales Service
Equipment support High efficiency and energy saving equipment since the start of normal commissioning, to ensure the normal operation of the equipment.
Service scheme Monthly, quarterly regular arrangement of personnel to the user phone or on-site equipment operation inspection, testing work, timely understanding of unit operation dynamics, effective answer to user equipment operation questions, and do the corresponding need to improve maintenance, maintenance, to ensure the long-term effective work of the equipment, while providing service reports every time.
Technical service As long as the user needs equipment and technical help and consultation, the company will accurately reply within 2 hours, and provide the relevant technical information.
Service team We have a CHINAMFG theoretical knowledge, practical ability of strong service team and high-quality management team.
Corresponding time Our company will respond within 2 hours after receiving the notification of the failure of the user’s equipment, provide the fastest solution, and arrange technicians to arrive at the scene as soon as necessary.
Warranty commitment High efficiency and energy saving equipment since the start of normal commissioning, the whole machine warranty for 1 year.
FAQ
Q1: What’s your delivery time?
O: It takes about 15 days, if there is any urgent order, please contact us.
Q2: How long is your air compressor warranty?
O: One year for the whole machine when the compressor leave our factory.
Q3: How about your after-sales service?
O:1. Provide customers with installation and commissioning online instructions.
2. Well-trained engineers available to overseas service
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | 7*24 |
|---|---|
| Warranty: | 1 Year |
| Lubrication Style: | Lubricated |
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Installation Type: | Stationary Type |
| Customization: |
Available
|
|
|---|
.webp)
What is the role of air compressors in power generation?
Air compressors play a significant role in power generation, supporting various operations and equipment within the industry. Here are some key roles of air compressors in power generation:
1. Combustion Air Supply:
Air compressors are used to supply compressed air for the combustion process in power generation. In fossil fuel power plants, such as coal-fired or natural gas power plants, compressed air is required to deliver a steady flow of air to the burners. The compressed air helps in the efficient combustion of fuel, enhancing the overall performance and energy output of the power plant.
2. Instrumentation and Control:
Air compressors are utilized for instrumentation and control systems in power generation facilities. Compressed air is used to operate pneumatic control valves, actuators, and other pneumatic devices that regulate the flow of steam, water, and gases within the power plant. The reliable and precise control provided by compressed air ensures efficient and safe operation of various processes and equipment.
3. Cooling and Ventilation:
In power generation, air compressors are involved in cooling and ventilation applications. Compressed air is used to drive air-operated cooling fans and blowers, providing adequate airflow for cooling critical components such as generators, transformers, and power electronics. The compressed air also assists in maintaining proper ventilation in control rooms, substations, and other enclosed spaces, helping to dissipate heat and ensure a comfortable working environment.
4. Cleaning and Maintenance:
Air compressors are employed for cleaning and maintenance tasks in power generation facilities. Compressed air is utilized to blow away dust, dirt, and debris from equipment, machinery, and electrical panels. It helps in maintaining the cleanliness and optimal performance of various components, reducing the risk of equipment failure and improving overall reliability.
5. Pneumatic Tools and Equipment:
In power generation plants, air compressors provide the necessary compressed air for operating pneumatic tools and equipment. These tools include impact wrenches, pneumatic drills, grinders, and sandblasting equipment, which are utilized for installation, maintenance, and repair tasks. The high-pressure air generated by compressors enables efficient and reliable operation of these tools, enhancing productivity and reducing manual effort.
6. Nitrogen Generation:
Sometimes, air compressors are used in power generation for nitrogen generation. Compressed air is passed through a nitrogen generator system, which separates nitrogen from other components of air, producing a high-purity nitrogen gas stream. Nitrogen is commonly used in power plant applications, such as purging systems, blanketing in transformers, and generator cooling, due to its inert properties and low moisture content.
7. Start-up and Emergency Systems:
Air compressors are an integral part of start-up and emergency systems in power generation. Compressed air is utilized to power pneumatic starters for gas turbines, providing the initial rotation needed to start the turbine. In emergency situations, compressed air is also used to actuate emergency shutdown valves, safety systems, and fire suppression equipment, ensuring the safe operation and protection of the power plant.
Overall, air compressors contribute to the efficient and reliable operation of power generation facilities, supporting combustion processes, control systems, cooling, cleaning, and various other applications critical to the power generation industry.
What are the environmental considerations when using air compressors?
When using air compressors, there are several environmental considerations to keep in mind. Here’s an in-depth look at some of the key factors:
Energy Efficiency:
Energy efficiency is a crucial environmental consideration when using air compressors. Compressing air requires a significant amount of energy, and inefficient compressors can consume excessive power, leading to higher energy consumption and increased greenhouse gas emissions. It is important to choose energy-efficient air compressors that incorporate features such as Variable Speed Drive (VSD) technology and efficient motor design, as they can help minimize energy waste and reduce the carbon footprint.
Air Leakage:
Air leakage is a common issue in compressed air systems and can contribute to energy waste and environmental impact. Leaks in the system result in the continuous release of compressed air, requiring the compressor to work harder and consume more energy to maintain the desired pressure. Regular inspection and maintenance of the compressed air system to detect and repair leaks can help reduce air loss and improve overall energy efficiency.
Noise Pollution:
Air compressors can generate significant noise levels during operation, which can contribute to noise pollution. Prolonged exposure to high noise levels can have detrimental effects on human health and well-being and can also impact the surrounding environment and wildlife. It is important to consider noise reduction measures such as sound insulation, proper equipment placement, and using quieter compressor models to mitigate the impact of noise pollution.
Emissions:
While air compressors do not directly emit pollutants, the electricity or fuel used to power them can have an environmental impact. If the electricity is generated from fossil fuels, the associated emissions from power plants contribute to air pollution and greenhouse gas emissions. Choosing energy sources with lower emissions, such as renewable energy, can help reduce the environmental impact of operating air compressors.
Proper Waste Management:
Proper waste management is essential when using air compressors. This includes the appropriate disposal of compressor lubricants, filters, and other maintenance-related materials. It is important to follow local regulations and guidelines for waste disposal to prevent contamination of soil, water, or air and minimize the environmental impact.
Sustainable Practices:
Adopting sustainable practices can further reduce the environmental impact of using air compressors. This can include implementing preventive maintenance programs to optimize performance, reducing idle time, and promoting responsible use of compressed air by avoiding overpressurization and optimizing system design.
By considering these environmental factors and taking appropriate measures, it is possible to minimize the environmental impact associated with the use of air compressors. Choosing energy-efficient models, addressing air leaks, managing waste properly, and adopting sustainable practices can contribute to a more environmentally friendly operation.
What is the role of air compressor tanks?
Air compressor tanks, also known as receiver tanks or air receivers, play a crucial role in the operation of air compressor systems. They serve several important functions:
1. Storage and Pressure Regulation: The primary role of an air compressor tank is to store compressed air. As the compressor pumps air into the tank, it accumulates and pressurizes the air. The tank acts as a reservoir, allowing the compressor to operate intermittently while providing a steady supply of compressed air during periods of high demand. It helps regulate and stabilize the pressure in the system, reducing pressure fluctuations and ensuring a consistent supply of air.
2. Condensation and Moisture Separation: Compressed air contains moisture, which can condense as the air cools down inside the tank. Air compressor tanks are equipped with moisture separators or drain valves to collect and remove this condensed moisture. The tank provides a space for the moisture to settle, allowing it to be drained out periodically. This helps prevent moisture-related issues such as corrosion, contamination, and damage to downstream equipment.
3. Heat Dissipation: During compression, air temperature increases. The air compressor tank provides a larger surface area for the compressed air to cool down and dissipate heat. This helps prevent overheating of the compressor and ensures efficient operation.
4. Pressure Surge Mitigation: Air compressor tanks act as buffers to absorb pressure surges or pulsations that may occur during compressor operation. These surges can be caused by variations in demand, sudden changes in airflow, or the cyclic nature of reciprocating compressors. The tank absorbs these pressure fluctuations, reducing stress on the compressor and other components, and providing a more stable and consistent supply of compressed air.
5. Energy Efficiency: Air compressor tanks contribute to energy efficiency by reducing the need for the compressor to run continuously. The compressor can fill the tank during periods of low demand and then shut off when the desired pressure is reached. This allows the compressor to operate in shorter cycles, reducing energy consumption and minimizing wear and tear on the compressor motor.
6. Emergency Air Supply: In the event of a power outage or compressor failure, the stored compressed air in the tank can serve as an emergency air supply. This can provide temporary air for critical operations, allowing time for maintenance or repairs to be carried out without disrupting the overall workflow.
Overall, air compressor tanks provide storage, pressure regulation, moisture separation, heat dissipation, pressure surge mitigation, energy efficiency, and emergency backup capabilities. They are vital components that enhance the performance, reliability, and longevity of air compressor systems in various industrial, commercial, and personal applications.
editor by CX 2024-05-22
China manufacturer High Quality ASME 7.5kw/11kw/15kw/22kw and 8bar/10bar/15bar/16bar VSD Permanent Magnet High Pressure Electric AC All in One Industry Rotary Screw Air Compressor air compressor portable
Product Description
Detailed Photos
High Quality ASME 7.5kw/11kw/15kw/22kw and 8bar/10bar/15bar/16bar VSD Premanent Magnet High Pressure Electric AC All in One Industry Rotary Screw Air Compressor
Description&Advantages
Product Descriptions:
High-pressure series compressors, medium-to-high pressure compressors for oil fields, general-purpose piston compressors, oil-free compressors of DW, VW, MZD, SF types, liquefied petroleum gas (LPG) circulation compressors, natural gas and gas bottle filling series compressors, and various types of pressure vessels. We can provide compressors with a discharge capacity ranging from 300 to 12000 nm³/h and discharge pressures from 0.2 to 45 MPa, suitable for compressing air, nitrogen, liquefied petroleum gas, coal gas, natural gas, carbon dioxide, propane, ethylene, ammonia, difluoroethane, and other mediem. With over 600 different models, our products are widely used in urban construction, petroleum, coal, geology, chemical, metallurgy, machinery manufacturing, medical, food and beverage, liquefied gas stations, natural gas stations, and other fields
ASC Compressor Factory are oil-free lubrication reciprocating piston compressors developed in collaboration with the German company CHINAMFG DEMAG. These models are known for their low energy consumption, minimal noise, reduced vibration, high reliability, and easy operation.
Each unit primarily consists of the compressor mainframe, electric motor, common base frame, air system, cooling system, lubrication system, instrument control system, drainage system, and electrical system. All components are generally installed on a single common base frame, which is then mounted on a concrete foundation, making it a fixed-type gas station. The connections between the equipment and the fixing points to the base are detachable, making transportation, installation, operation, and maintenance extremely convenient.
Advantages:
Our products, incorporating technology from Germany’s CHINAMFG Demag companies, exhibit high reliability. Wearable parts like gas valves and piston rings use products from Austria’s Hoerbiger company, with a lifespan exceeding 8000 hours. The system supports soft starting, allowing frequent start and stop cycles for the compressor. It features a wide intake range for broad adaptability. The overall skid-mounted structure results in low noise and is easy to install in urban areas, leading to investment savings.
It is equipped with a CHINAMFG PLC control system for high automation, ABB soft start (or variable frequency), and features automatic shutdown with audible and visual alarms in case of faults
Product Parameters
| Medium to High Compressor Parameter Sheet | ||||||||
| No | Model | Medium | Capacity | Inlet Pressure | Outlet Pressure | Rotation | Power | Cooling Method |
| nm3/h | MPa | MPa | r/min | KW | ||||
| 1 | DW-2.4/(18~25)-50 | Raw Gas | 2700 | 1.8~2.5 | 5 | 980 | 160 | Water |
| 2 | DW-5.5/(13-15)-26 | Nitrogen | 4500 | 1.3~1.5 | 2.6 | 740 | 160 | Water |
| 3 | VW-4.6/52 | BOG | 250 | Atmospheric Pressure | 5.2 | 740 | 75 | Closed loop |
| 4 | DWF-7/(2-4)-30 | Wellhead Gas | 2100 | 0.2~0.4 | 3 | 740 | 200 | Air |
| 5 | VWD-3.2/(0-0.2)-40 | Biogas | 200 | 0~0.02 | 4 | 740 | 45 | Closed loop |
| 6 | DW-4/5-41 | Exhaust Gas | 1200 | 0.5 | 4.1 | 980 | 160 | Water |
| 7 | VW-4.1/(36.8-44.7)- (39.9-49.9) |
Regenerated Gas | 8865 | 3.68~4.47 | 3.99~4.99 | 980 | 132 | Water |
| 8 | 2VW-18/0.05-90 | BOG | 1100 | 0.005 | 9 | 980 | 250 | Water |
| 9 | VW-4.8/48-54 | Natural Gas | 12000 | 4.8 | 5.4 | 980 | 132 | Water |
| 10 | VW-2/120 | Carbon Monoxide | 1200 | Atmospheric Pressure | 12 | 740 | 37 | Water |
| 11 | VW-2.5/120 | Carbon Monoxide | 1200 | Atmospheric Pressure | 12 | 740 | 45 | Water |
| High-Pressure Compressor (Pipeline Blowing) Specification Table | ||||||||
| No | Model | Medium | Capacity | Inlet Pressure | Outlet Pressure | Rotation | Power | Cooling Method |
| m3/h | MPa | MPa | r/min | W | ||||
| 1 | SF-10/250 | Air | 600 | Atm | 25 | 1330 | 258.5 (Diesel Motor) | Air |
| 2 | SF-10/150 | Air | 600 | Atm | 15 | 1330 | 258.5 (Diesel Motor) | |
| 3 | SF-7.5/250 | Air | 450 | Atm | 25 | 980 | 160 (Electric Motor) | |
| 4 | SF-7.5/150 | Air | 450 | Atm | 15 | 980 | 132 (Electric Motor) | |
| 5 | SF-8.5/250 | Air | 510 | Atm | 15 | 980 | 200 (Electric Motor) | |
| 6 | W-10/60 | Air | 600 | Atm | 6 | 1330 | 132 (Electric Motor) | |
| High-Pressure Compressor (Oilfield Membrane Nitrogen Generation) Parameter Table | |||||||
| Model | Flow Rate | Outlet Pressure | Air compressor form and series | Form and series of nitrogen booster compressor | Drive parameter | Power | Membrane Module Qty |
| nm3/h | MPa | KW | |||||
| MZD-300/250 | 300 | 25 | Screw type single-stage | V-type piston three-stage | 90KW+55KW | 300 | 4 |
| MZD-300/350 | 300 | 35 | Screw type single-stage | V-type piston four-stage | 90KW+55KW | 300 | 4 |
| MZD-300/250-C | 300 | 25 | Screw type single-stage | V-type piston three-stage | TBD234V6 | / | 4 |
| MZD-300/350-C | 300 | 35 | Screw type single-stage | V-type piston four-stage | TBD234V6 | / | 4 |
| MZD-600/250 | 600 | 25 | Screw type single-stage | V-type piston three-stage | 185KW+132KW | 500 | 8 |
| MZD-600/350 | 600 | 35 | Screw type single-stage | V-type piston four-stage | 185KW+132KW | 500 | 8 |
| MZD-600/250-C | 600 | 25 | Screw type single-stage | V-type piston three-stage | TBD234VB | / | 8 |
| MZD-600/350-C | 600 | 35 | Screw type single-stage | V-type piston four-stage | TBD234VB | / | 8 |
| MZD-900/250 | 900 | 25 | Screw type single-stage | V-type piston three-stage | 250KW+185KW | 800 | 12 |
| MZD-900/350 | 900 | 35 | Screw type single-stage | V-type piston four-stage | 250KW+185KW | 800 | 12 |
| MZD-1200/250 | 1200 | 25 | Screw type single-stage | V-type piston four-stage | 315KW+250KW | 880 | 16 |
| MZD-1200/350 | 1200 | 35 | Screw type single-stage | V-type piston four-stage | 315KW+250KW | 880 | 16 |
| MZD-1500/150 | 1200 | 15 | Screw type single-stage | V-type piston three-stage | 440KW+220KW | 880 | 20 |
Our Factory
Part of Customer Visit
Certifications & Testing
Related Product
FAQ
Q:Are you a factory?
A:Yes, we are indeed a factory. We specialize in manufacturing high-quality Air/Gas Compressors and are proud to be a primary source for these products.
Q:How long is your delivery time?
A:It varies depending on the specific situation. For our standard configuration compressors, the delivery time is around 30 days. For customized compressors, it usually takes about 30-45 days.
Q:What technical support do you offer?
A:We offer comprehensive technical support to our clients, including remote assistance for installation and commissioning processes. Additionally, we have a team of seasoned engineers ready to be deployed to international client locations for meticulous on-site debugging, installation, and post-installation services.
Q:What is your warranty period?
A:Our warranty policy is valid for a period of 18 months from the date of commissioning at the end customer’s site or 21 months from the date of receipt by the purchaser, whichever comes first. This comprehensive coverage is designed to ensure total customer satisfaction and the reliability of our products
Q:How do you package the compressors?
A:For smaller compressors, we utilize robust plywood boxes that conform to export specifications.
For the larger units, we strategically place them in freight containers, implementing secure fastening methods to safeguard against any potential damage during the shipping process.
Q:What are your payment terms?
A:Usually, the payment is made by T/T with a 30% down payment CHINAMFG confirmation of the Proforma Invoice (PI), and the balance is to be paid after inspection and before shipment. We accept both TT and L/C at sight.
Send message Get product Offer & Brochure!!!
↓↓↓
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | Local Teams |
|---|---|
| Warranty: | 18 Months |
| Lubrication Style: | Customized |
| Cooling System: | Air Cooling/Water Cooling |
| Cylinder Arrangement: | Balanced Opposed Arrangement |
| Cylinder Position: | Customized |
| Samples: |
US$ 40000/Set
1 Set(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
.webp)
What are the energy-saving technologies available for air compressors?
There are several energy-saving technologies available for air compressors that help improve their efficiency and reduce energy consumption. These technologies aim to optimize the operation of air compressors and minimize energy losses. Here are some common energy-saving technologies used:
1. Variable Speed Drive (VSD) Compressors:
VSD compressors are designed to adjust the motor speed according to the compressed air demand. By varying the motor speed, these compressors can match the output to the actual air requirement, resulting in energy savings. VSD compressors are particularly effective in applications with varying air demands, as they can operate at lower speeds during periods of lower demand, reducing energy consumption.
2. Energy-Efficient Motors:
The use of energy-efficient motors in air compressors can contribute to energy savings. High-efficiency motors, such as those with premium efficiency ratings, are designed to minimize energy losses and operate more efficiently than standard motors. By using energy-efficient motors, air compressors can reduce energy consumption and achieve higher overall system efficiency.
3. Heat Recovery Systems:
Air compressors generate a significant amount of heat during operation. Heat recovery systems capture and utilize this wasted heat for other purposes, such as space heating, water heating, or preheating process air or water. By recovering and utilizing the heat, air compressors can provide additional energy savings and improve overall system efficiency.
4. Air Receiver Tanks:
Air receiver tanks are used to store compressed air and provide a buffer during periods of fluctuating demand. By using appropriately sized air receiver tanks, the compressed air system can operate more efficiently. The tanks help reduce the number of starts and stops of the air compressor, allowing it to run at full load for longer periods, which is more energy-efficient than frequent cycling.
5. System Control and Automation:
Implementing advanced control and automation systems can optimize the operation of air compressors. These systems monitor and adjust the compressed air system based on demand, ensuring that only the required amount of air is produced. By maintaining optimal system pressure, minimizing leaks, and reducing unnecessary air production, control and automation systems help achieve energy savings.
6. Leak Detection and Repair:
Air leaks in compressed air systems can lead to significant energy losses. Regular leak detection and repair programs help identify and fix air leaks promptly. By minimizing air leakage, the demand on the air compressor is reduced, resulting in energy savings. Utilizing ultrasonic leak detection devices can help locate and repair leaks more efficiently.
7. System Optimization and Maintenance:
Proper system optimization and routine maintenance are essential for energy savings in air compressors. This includes regular cleaning and replacement of air filters, optimizing air pressure settings, ensuring proper lubrication, and conducting preventive maintenance to keep the system running at peak efficiency.
By implementing these energy-saving technologies and practices, air compressor systems can achieve significant energy efficiency improvements, reduce operational costs, and minimize environmental impact.
.webp)
What is the energy efficiency of modern air compressors?
The energy efficiency of modern air compressors has significantly improved due to advancements in technology and design. Here’s an in-depth look at the energy efficiency features and factors that contribute to the efficiency of modern air compressors:
Variable Speed Drive (VSD) Technology:
Many modern air compressors utilize Variable Speed Drive (VSD) technology, also known as Variable Frequency Drive (VFD). This technology allows the compressor motor to adjust its speed according to the compressed air demand. By matching the motor speed to the required airflow, VSD compressors can avoid excessive energy consumption during periods of low demand, resulting in significant energy savings compared to fixed-speed compressors.
Air Leakage Reduction:
Air leakage is a common issue in compressed air systems and can lead to substantial energy waste. Modern air compressors often feature improved sealing and advanced control systems to minimize air leaks. By reducing air leakage, the compressor can maintain optimal pressure levels more efficiently, resulting in energy savings.
Efficient Motor Design:
The motor of an air compressor plays a crucial role in its energy efficiency. Modern compressors incorporate high-efficiency electric motors that meet or exceed established energy efficiency standards. These motors are designed to minimize energy losses and operate more efficiently, reducing overall power consumption.
Optimized Control Systems:
Advanced control systems are integrated into modern air compressors to optimize their performance and energy consumption. These control systems monitor various parameters, such as air pressure, temperature, and airflow, and adjust compressor operation accordingly. By precisely controlling the compressor’s output to match the demand, these systems ensure efficient and energy-saving operation.
Air Storage and Distribution:
Efficient air storage and distribution systems are essential for minimizing energy losses in compressed air systems. Modern air compressors often include properly sized and insulated air storage tanks and well-designed piping systems that reduce pressure drops and minimize heat transfer. These measures help to maintain a consistent and efficient supply of compressed air throughout the system, reducing energy waste.
Energy Management and Monitoring:
Some modern air compressors feature energy management and monitoring systems that provide real-time data on energy consumption and performance. These systems allow operators to identify energy inefficiencies, optimize compressor settings, and implement energy-saving practices.
It’s important to note that the energy efficiency of an air compressor also depends on factors such as the specific model, size, and application. Manufacturers often provide energy efficiency ratings or specifications for their compressors, which can help in comparing different models and selecting the most efficient option for a particular application.
Overall, modern air compressors incorporate various energy-saving technologies and design elements to enhance their efficiency. Investing in an energy-efficient air compressor not only reduces operational costs but also contributes to sustainability efforts by minimizing energy consumption and reducing carbon emissions.
What are the key components of an air compressor system?
An air compressor system consists of several key components that work together to generate and deliver compressed air. Here are the essential components:
1. Compressor Pump: The compressor pump is the heart of the air compressor system. It draws in ambient air and compresses it to a higher pressure. The pump can be reciprocating (piston-driven) or rotary (screw, vane, or scroll-driven) based on the compressor type.
2. Electric Motor or Engine: The electric motor or engine is responsible for driving the compressor pump. It provides the power necessary to operate the pump and compress the air. The motor or engine’s size and power rating depend on the compressor’s capacity and intended application.
3. Air Intake: The air intake is the opening or inlet through which ambient air enters the compressor system. It is equipped with filters to remove dust, debris, and contaminants from the incoming air, ensuring clean air supply and protecting the compressor components.
4. Compression Chamber: The compression chamber is where the actual compression of air takes place. In reciprocating compressors, it consists of cylinders, pistons, valves, and connecting rods. In rotary compressors, it comprises intermeshing screws, vanes, or scrolls that compress the air as they rotate.
5. Receiver Tank: The receiver tank, also known as an air tank, is a storage vessel that holds the compressed air. It acts as a buffer, allowing for a steady supply of compressed air during peak demand periods and reducing pressure fluctuations. The tank also helps separate moisture from the compressed air, allowing it to condense and be drained out.
6. Pressure Relief Valve: The pressure relief valve is a safety device that protects the compressor system from over-pressurization. It automatically releases excess pressure if it exceeds a predetermined limit, preventing damage to the system and ensuring safe operation.
7. Pressure Switch: The pressure switch is an electrical component that controls the operation of the compressor motor. It monitors the pressure in the system and automatically starts or stops the motor based on pre-set pressure levels. This helps maintain the desired pressure range in the receiver tank.
8. Regulator: The regulator is a device used to control and adjust the output pressure of the compressed air. It allows users to set the desired pressure level for specific applications, ensuring a consistent and safe supply of compressed air.
9. Air Outlet and Distribution System: The air outlet is the point where the compressed air is delivered from the compressor system. It is connected to a distribution system comprising pipes, hoses, fittings, and valves that carry the compressed air to the desired application points or tools.
10. Filters, Dryers, and Lubricators: Depending on the application and air quality requirements, additional components such as filters, dryers, and lubricators may be included in the system. Filters remove contaminants, dryers remove moisture from the compressed air, and lubricators provide lubrication to pneumatic tools and equipment.
These are the key components of an air compressor system. Each component plays a crucial role in the generation, storage, and delivery of compressed air for various industrial, commercial, and personal applications.
editor by CX 2024-04-27
China Standard Highly Brand Bmvf37 Ridgid Permanent Magnet Industrial Screw Air Compressor air compressor oil
Product Description
Product Introduction
Highly Brand BMVF37 Ridgid Permanent Magnet Industrial Screw Air Compressor
Oil injected screw air compressor has become the mainstream of air compressor development in the world. It has extremely superior and reliable performance. It has small vibration, low noise, high efficiency and few vulnerable parts. It has incomparable performance advantages of piston compressor (under the same exhaust pressure). The precise coordination between the male and female rotors and between the rotor and the main engine shell reduces the back- flow leakage and improves the efficiency; Only the rotors are meshed with each other, and reciprocating motion without cylinder, which reduces the source of vibration and noise; The unique lubrication method brings many advantages:
1. With the pressure difference generated by itself, lubricating oil is continuously injected into the compression chamber and bearing to simplify the complex mechanical structure.
2. The injected lubricating oil can form oil film between the rotors, and the primary can take secondary rotor to rotate, Without the help of high precision synchronous gear.
3. The injected lubricating oil can increase the air tightness.
4. The lubricating oil absorbs a lot of compression heat, so even if the compression ratio reaches 16, The head can still be controlled below the carbon deposition and degradation temperature of general lubricating oil, There is no friction between the rotor and the outside of the machine due to different expansion coefficient.
5. Lubricating oil reduces the noise caused by high frequency compression.
6. A small amount of oil into the compressed air, pneumatic tools have a certain lubrication.
Product Parameters
|
Screw group |
5: 6 Gear rotor |
|
|
Compression method |
Continuous, CHINAMFG |
|
|
Compressed air outlet pressure |
0.65-1.0MPa |
|
|
Compressed air outlet temperature |
Air-cooled |
|
|
Compressed air outlet temperature |
10ºC~15ºC higher than the ambient temperature |
|
|
Volume of Lubricating Oil |
About 16.5liters |
|
|
Motor speed |
N=3600r/min |
|
|
Rated power |
37kw |
|
|
Air capacity |
V=5.05-6.35m3/min |
|
|
Weight |
500kg |
|
|
Upper air temperature |
45ºC |
|
|
Lower limit of air temperature |
0ºC |
|
|
Fuel consumption |
Exhaust oil content is less than 3PPM |
|
|
Noise level |
76dB(A) |
|
|
Dimensions (length×width×height) (mm) |
1340x850x1330 |
|
Detailed Photos
Wider range of speed regulation, higher accuracy of regulation, wider range of air supply pressure and higher energy efficiency.
The patented design of weak magnetic control, pressure control and simple and stable permanent magnet motor open-loop control can adapt to a variety of adverse working conditions and make the system more stable.
The patented design of weak magnetic control, pressure control and simple and stable permanent magnet motor open-loop control can adapt to a variety of adverse working conditions and make the system more stable.
Motor and screw host coaxial, higher efficiency. The BMVF series is the CHINAMFG industry to achieve the screw host, synchronous motor, permanent magnet control electrical control synchronous design, and to achieve the advantages of cooperation.
Specification
|
Model |
Working Pressure |
Capacity |
Motor Power |
Connector |
Weight |
Noise |
Dimension |
|
Bar |
m³/min |
kw |
kg |
dB(A) |
mm |
||
|
BMVF7.5G |
0.65-1.0 |
1.0-1.25 |
7.5 |
G3/4 |
200 |
72 |
800*510*800 |
| BMVF11G |
0.65-1.0 |
1.5-1.85 |
11 |
G1
|
260 |
73 |
1000*670*1090 |
| BMVF15G | 0.65-1.0 |
2.05-2.35 |
15 |
280 |
73 |
1000*670*1090 |
|
|
BMVF22G |
0.65-1.0 |
2.95-3.95 |
22 |
390 |
74 |
1200*800*1120 |
|
| BMVF37G | 0.65-1.0 |
5.05-6.35 |
37 |
600 |
76 |
1340*850*1300 |
|
|
BMVF45G |
0.65-1.0 |
6.45-8.2 |
45 |
800 |
78 |
1480*1030*1365 |
|
| BMVF55G | 0.65-1.0 |
8.2-9.85 |
55 |
810 |
80 |
||
| BMVF75 | 0.65-1.0 |
10.5-13.1 |
75 |
G2 |
1280 |
81 |
1800*1190*1710 |
| BMVF90 | 0.65-1.0 |
12.5-15.5 |
90 |
1300 |
81 |
||
| BMVF110 | 0.65-0.8 |
22 |
110 |
DN65 |
1850 |
82 |
2700*1230*1730 |
| BMVF132 | 0.65-0.8 |
24 |
132 |
2270 |
82 |
Why Choose Us
CHINAMFG group is a state-level large scale enterprise headquartered in HangZhou, ZHangZhoug province, China. Over the last 60 years CHINAMFG Group has grown to become a significant diversified engineering company developing high value machinery for industry worldwide. CHINAMFG group is the largest rock drill manufacturer in the world, and the largest air compressor manufacturer in China. Exports are shipped to over 25 countries .Today we produce over 30 000 rotary screw and 250 000 reciprocating compressors annually.By the year of 2014 our sales amount was close to RMB 2 billion. CHINAMFG group also has the high-quality customer service system.
Our company is the authorized agent of CHINAMFG Group, specializing in air compressor, energy-saving transformation service and mining engineering construction machinery. We provide comprehensive technical support and after-sales service to customers.
CHINAMFG is headquartered in HangZhou in ZHangZhoug, China. It has subsidiaries in ZheJiang , Chgonqing, ZheJiang , ZheJiang , Hong Kong, Seattle, San Diego, Orlando, Melbourne, Singapore, Jakarta, Leobersdorf, Budapest and Belgrade, as well as offices in Russia, Colombia, Brazil, Korea, Malaysia and Thailand.
Advanced Equipment–Advanced equipment guarantees product quality. Over the years, we have received unanimous praise from overseas users for our integrity and high-quality product quality.
Packaging
The air compressor is guaranteed for 1 year. In addition to wearing parts and consumables, if the spare parts within the warranty period are broken, the company provides free spare parts replacement, but the buyer needs to pay the freight. Please ask customer service for specific warranty rules.
FAQ
Contacts
ZHangZhoug Stars Energy Saving Technology Co., Ltd.
If you want to know more information, please contact us!
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | One Year Warranty |
|---|---|
| Warranty: | One Year |
| Lubrication Style: | Lubricated |
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Cylinder Position: | Horizontal |
| Samples: |
US$ 2340/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
.webp)
Can air compressors be used for painting and sandblasting?
Yes, air compressors can be used for both painting and sandblasting applications. Here’s a closer look at how air compressors are utilized for painting and sandblasting:
Painting:
Air compressors are commonly used in painting processes, especially in automotive, industrial, and construction applications. Here’s how they are involved:
- Spray Guns: Air compressors power spray guns used for applying paint coatings. The compressed air atomizes the paint, creating a fine mist that can be evenly sprayed onto surfaces. The pressure and volume of the compressed air impact the spray pattern, coverage, and overall finish quality.
- Paint Mixers and Agitators: Compressed air is often used to power mixers and agitators that ensure proper blending of paint components. These devices use the compressed air to stir or circulate the paint, preventing settling and maintaining a consistent mixture.
- Airbrushing: Air compressors are essential for airbrushing techniques, which require precise control over airflow and pressure. Airbrushes are commonly used in artistic applications, such as illustrations, murals, and fine detailing work.
Sandblasting:
Air compressors play a crucial role in sandblasting operations, which involve propelling abrasive materials at high velocity to clean, etch, or prepare surfaces. Here’s how air compressors are used in sandblasting:
- Blasting Cabinets: Air compressors power blasting cabinets or booths, which are enclosed spaces where the sandblasting process takes place. The compressed air propels the abrasive media, such as sand or grit, through a nozzle or gun, creating a forceful stream that impacts the surface being treated.
- Abrasive Blasting Pots: Air compressors supply air to abrasive blasting pots or tanks that store and pressurize the abrasive media. The compressed air from the compressor enters the pot, pressurizing it and allowing for a controlled release of the abrasive material during the sandblasting process.
- Air Dryers and Filters: In sandblasting applications, it is crucial to have clean, dry air to prevent moisture and contaminants from affecting the abrasive blasting process and the quality of the surface being treated. Air compressors may be equipped with air dryers and filters to remove moisture, oil, and impurities from the compressed air.
When using air compressors for painting or sandblasting, it is important to consider factors such as the compressor’s pressure and volume output, the specific requirements of the application, and the type of tools or equipment being used. Consult the manufacturer’s guidelines and recommendations to ensure the air compressor is suitable for the intended painting or sandblasting tasks.
Proper safety measures, such as wearing protective gear and following established protocols, should always be followed when working with air compressors for painting and sandblasting applications.
What is the energy efficiency of modern air compressors?
The energy efficiency of modern air compressors has significantly improved due to advancements in technology and design. Here’s an in-depth look at the energy efficiency features and factors that contribute to the efficiency of modern air compressors:
Variable Speed Drive (VSD) Technology:
Many modern air compressors utilize Variable Speed Drive (VSD) technology, also known as Variable Frequency Drive (VFD). This technology allows the compressor motor to adjust its speed according to the compressed air demand. By matching the motor speed to the required airflow, VSD compressors can avoid excessive energy consumption during periods of low demand, resulting in significant energy savings compared to fixed-speed compressors.
Air Leakage Reduction:
Air leakage is a common issue in compressed air systems and can lead to substantial energy waste. Modern air compressors often feature improved sealing and advanced control systems to minimize air leaks. By reducing air leakage, the compressor can maintain optimal pressure levels more efficiently, resulting in energy savings.
Efficient Motor Design:
The motor of an air compressor plays a crucial role in its energy efficiency. Modern compressors incorporate high-efficiency electric motors that meet or exceed established energy efficiency standards. These motors are designed to minimize energy losses and operate more efficiently, reducing overall power consumption.
Optimized Control Systems:
Advanced control systems are integrated into modern air compressors to optimize their performance and energy consumption. These control systems monitor various parameters, such as air pressure, temperature, and airflow, and adjust compressor operation accordingly. By precisely controlling the compressor’s output to match the demand, these systems ensure efficient and energy-saving operation.
Air Storage and Distribution:
Efficient air storage and distribution systems are essential for minimizing energy losses in compressed air systems. Modern air compressors often include properly sized and insulated air storage tanks and well-designed piping systems that reduce pressure drops and minimize heat transfer. These measures help to maintain a consistent and efficient supply of compressed air throughout the system, reducing energy waste.
Energy Management and Monitoring:
Some modern air compressors feature energy management and monitoring systems that provide real-time data on energy consumption and performance. These systems allow operators to identify energy inefficiencies, optimize compressor settings, and implement energy-saving practices.
It’s important to note that the energy efficiency of an air compressor also depends on factors such as the specific model, size, and application. Manufacturers often provide energy efficiency ratings or specifications for their compressors, which can help in comparing different models and selecting the most efficient option for a particular application.
Overall, modern air compressors incorporate various energy-saving technologies and design elements to enhance their efficiency. Investing in an energy-efficient air compressor not only reduces operational costs but also contributes to sustainability efforts by minimizing energy consumption and reducing carbon emissions.
.webp)
How do oil-lubricated and oil-free air compressors differ?
Oil-lubricated and oil-free air compressors differ in terms of their lubrication systems and the presence of oil in their operation. Here are the key differences:
Oil-Lubricated Air Compressors:
1. Lubrication: Oil-lubricated air compressors use oil for lubricating the moving parts, such as pistons, cylinders, and bearings. The oil forms a protective film that reduces friction and wear, enhancing the compressor’s efficiency and lifespan.
2. Performance: Oil-lubricated compressors are known for their smooth and quiet operation. The oil lubrication helps reduce noise levels and vibration, resulting in a more comfortable working environment.
3. Maintenance: These compressors require regular oil changes and maintenance to ensure the proper functioning of the lubrication system. The oil filter may need replacement, and the oil level should be regularly checked and topped up.
4. Applications: Oil-lubricated compressors are commonly used in applications that demand high air quality and continuous operation, such as industrial settings, workshops, and manufacturing facilities.
Oil-Free Air Compressors:
1. Lubrication: Oil-free air compressors do not use oil for lubrication. Instead, they utilize alternative materials, such as specialized coatings, self-lubricating materials, or water-based lubricants, to reduce friction and wear.
2. Performance: Oil-free compressors generally have a higher airflow capacity, making them suitable for applications where a large volume of compressed air is required. However, they may produce slightly more noise and vibration compared to oil-lubricated compressors.
3. Maintenance: Oil-free compressors typically require less maintenance compared to oil-lubricated ones. They do not need regular oil changes or oil filter replacements. However, it is still important to perform routine maintenance tasks such as air filter cleaning or replacement.
4. Applications: Oil-free compressors are commonly used in applications where air quality is crucial, such as medical and dental facilities, laboratories, electronics manufacturing, and painting applications. They are also favored for portable and consumer-grade compressors.
When selecting between oil-lubricated and oil-free air compressors, consider the specific requirements of your application, including air quality, noise levels, maintenance needs, and expected usage. It’s important to follow the manufacturer’s recommendations for maintenance and lubrication to ensure the optimal performance and longevity of the air compressor.
editor by CX 2024-04-11
China high quality High Quality ASME 7.5kw/11kw/15kw/22kw and 8bar/10bar/15bar/16bar VSD Premanent Magnet High Pressure Electric AC All in One Industry Rotary Screw Air Compressor air compressor price
Product Description
Technical parameters
8/10 Bar
| Model | Max Working Pressure |
Capacity | Motor Power | Air Tank Capacity | Connection | Net Weight |
Dimension (L*W*H) |
||
| — | bar | psig | m3/min | hp | kw | L | inch | kgs | mm |
| J7.5CTG-8 | 8 | 116 | 1.10 | 10 | 7.5 | 250 | G3/4″ | 350 | 1430*710*1470 |
| J7.5CTG-10 | 10 | 145 | 0.90 | ||||||
| J11CTG-8 | 8 | 116 | 1.60 | 15 | 11 | 400 | G3/4″ | 510 | 1850*950*1870 |
| J11CTG-10 | 10 | 145 | 1.40 | ||||||
| J15CTG-8 | 8 | 116 | 2.60 | 20 | 15 | 400 | G3/4″ | 510 | 1850*950*1870 |
| J15CTG-10 | 10 | 145 | 2.00 | ||||||
| J22CTG-8 | 8 | 116 | 3.60 | 30 | 22 | 400 | G1″ | 555 | 1850*950*1870 |
| J22CTG-10 | 10 | 145 | 3.00 | ||||||
16 Bar
| Model | Max Working Pressure |
Capacity | Motor Power | Air Tank Capacity |
Connection | Net Weight |
Dimension (L*W*H) |
||
| — | bar | psig | m3/min | hp | kw | L | inch | kgs | mm |
| J11CTG-16 | 16 | 217 | 1.10 | 15 | 11 | 400 | G3/4″ | 510 | 1850*950*1870 |
| J15CTG-16 | 16 | 217 | 1.50 | 20 | 15 | 400 | G3/4″ | 510 | 1850*950*1870 |
| J22CTG-16 | 16 | 217 | 2.30 | 30 | 22 | 400 | G1″ | 555 | 1850*950*1870 |
(If you do not have a suitable air compressor, welcome to browse our other models)
Parts Introduction
Color touch screen
1.Intelligent control system.
2.Easy to operate,intelligent display thr running situation.
Inovance inverter
1.Low noise,stepless speed regulation to protect the grid.
2.Quick response,stable air pressure,energy saving.
High efficient air-end
1.No power loss,high efficient transmission.
2.Low energy consumption,low maintenance cost.
Refrigerated air dryer
1.Remove 98% of the moisture in the air.
2.Perfect fit for the compressor.
Line Air filter
1.Make compressed air cleaner and protect your end machine.
2.Italian brand.
Product features
1.Small footpaint
| 22kw separate system floor area VS 22kw 4in1 system floor area (example) | 22kw separate system floor area | 22kw 4IN1 system floor area |
| Screw air compressor | 930*750*1205mm | 1850*950*1870mm |
| Air tank | 940*940*2220mm | |
| Air dryer & Line air filter | 500*860*880mm | |
| Compressor room size required (include the maintenance space) | L6000*W3000*H3200mm | L2500*W3000*H2500mm |
(A 22kw 4in1 screw air compressor system floor area is samller than a 22kw separate air compressor system, save your factory space.)
2.Plug and use
| A separate air compressor system need installnation the pipeline, take time and cost. For example, in China install a 22kw compressor system pipeline need to pay labor cost USD200 and material cost USD350 Total USD550. |
OLYMTECH 4IN1 compressor pipeline is connected before delivering, user get it and connect the power, plug and use, save time and cost! |
3.Upgraded water drain system
| Other brands line air filter match with manual drain, the condensate water from air tank, air dryer and air filter spilled all over the floor, makes the enviroment dirty and wet. |
OLYMTECH 4IN1 compressor line air filter match with auto drain. We collect the condensate water from air tank, air dryer and air filter, then drain the water together, keeps the enviroment clean and dry. |
4.Power connect
| Other brands air compressor and air dryer power are separate, need to connect 2 power, user need to prepare 1 phase and 3 phase power, it is complicated! |
OLYMTECH 4IN1 compressor and dryer power are combine, just need to connect the air compressor power, then can run the whole machine, easy to use. |
5.Energy saving solution
| Smart inverter(35%) A wide speed control range of frequency converter prevents unnecessary power consumption for no-load operation. |
No unnecessary pressure(6-8%) Constant pressure setting reduce the pressure drop, 1bar of unnecessarily high pressure correopnds to about 7% of the energy. |
Permanent magnet motor(2-5%) High efficiency IE3 permanent magnet motor reduces energy costs. |
Lossless direct drive(1-2%) The direct connectin between the air-end and motor has none of the transmission losses. |
Production line factory
Real factory
1.20 years screw air compressor prodcution experience.
2.Two owned factories.
3.Ten cooperation factories.
OEM/ODM service
OLYMTECH custom-make your logo and color. Details please check with our sales engineer.
Certificates:
company-Olymtech-Technology-Development-Co-Ltd-.html
120000m3 NEW FACTORY is coming in 2571, welcome to visit olymtech!
After Sales Service
Spare part support
Genuine spare parts supply.
Video support
24hour /7day online after-sales service for installation commissioning, trouble shooting.
File support
English user manual, maintenance book, etc.
Training support
Distributors sales and after-sales teaining.
Industry application
Meet the needs of all industries! Your best work partner!
Laser cutting: product/KERpZiUwZecL/China-Hot-Sale-Laser-Cutting-Machine-Used-ASME-CE-Pmvsd-All-in-One-4in1-Energy-Saving-Screw-Air-Compressor.html
(Detailed application details pages for other industries are still being added)
Why choose us
| Shipping solution Help you save shipping cost. |
Global Exhibition We have more than 10 years of exhibition experience. |
Customer Feedback Customers’ recognition of us is the driving force for us to move forward. |
Successful case Serves clients in 182 countries. |
Want to know more? Contact us right now!
FAQ
Q1: Why customer choose us?
O: CHINAMFG Technology Development Co, Ltd is a professional manufacturer for air compressor and after treatment equipment. We have more than 20 years experience in producing and exporting air compressor, air dryer and air filter.
Q2: Are you a manufacturer or trading company?
O: Our factory is located in ZheJiang China, we have research and develop center, advanced processing equipment, professional technicians, rich experience workers and after-sales team to offer good quality products and good service to our customers. We also can provide you the OEM&ODM service.
Q3: What’s your delivery time?
O: Generally 10 days, if urgently order, pls contact our sales in advance.
Q4: How long is your air compressor warranty?
O: One year for the whole machine when the compressor leave our factory.
Q5: How long could your air compressor be used?
O: Generally, more than 10 years.
Q6: What’s payment terms?
O: T/T, L/C, Paypal etc. Also we could accept USD, RMB, Euro and other currency (Pls contact our sales for more information.).
Q7: How about your customer service?
O: 24 hours on-line service available.
Q8: How about your after-sales service?
O: 1. Provide customers with installation and commissioning online instructions.
2. Well-trained engineers available to overseas service
3. World wide agents and after service available
———————————–BUY COMPRESSOR,CHOOSE OLYMTECH!———————————–
| After-sales Service: | 1 Year |
|---|---|
| Warranty: | 1 Year |
| Lubrication Style: | Lubricated |
| Samples: |
US$ 2500/Unit
1 Unit(Min.Order) | Order Sample |
|---|
| Customization: |
Available
|
|
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
.webp)
How are air compressors employed in the petrochemical industry?
Air compressors play a vital role in the petrochemical industry, where they are employed for various applications that require compressed air. The petrochemical industry encompasses the production of chemicals and products derived from petroleum and natural gas. Here’s an overview of how air compressors are utilized in the petrochemical industry:
1. Instrumentation and Control Systems:
Air compressors are used to power pneumatic instrumentation and control systems in petrochemical plants. These systems rely on compressed air to operate control valves, actuators, and other pneumatic devices that regulate processes such as flow control, pressure control, and temperature control. Compressed air provides a reliable and clean source of energy for these critical control mechanisms.
2. Pneumatic Tools and Equipment:
Petrochemical plants often utilize pneumatic tools and equipment for various tasks such as maintenance, repair, and construction activities. Air compressors supply the necessary compressed air to power these tools, including pneumatic drills, impact wrenches, grinders, sanders, and painting equipment. The versatility and convenience of compressed air make it an ideal energy source for a wide range of pneumatic tools used in the industry.
3. Process Air and Gas Supply:
Petrochemical processes often require a supply of compressed air and gases for specific applications. Air compressors are employed to generate compressed air for processes such as oxidation, combustion, and aeration. They may also be used to compress gases like nitrogen, hydrogen, and oxygen, which are utilized in various petrochemical reactions and treatment processes.
4. Cooling and Ventilation:
Petrochemical plants require adequate cooling and ventilation systems to maintain optimal operating conditions and ensure the safety of personnel. Air compressors are used to power cooling fans, blowers, and air circulation systems that help maintain the desired temperature, remove heat generated by equipment, and provide ventilation in critical areas.
5. Nitrogen Generation:
Nitrogen is widely used in the petrochemical industry for applications such as blanketing, purging, and inerting. Air compressors are utilized in nitrogen generation systems, where they compress atmospheric air, which is then passed through a nitrogen separation process to produce high-purity nitrogen gas. This nitrogen is used for various purposes, including preventing the formation of explosive mixtures, protecting sensitive equipment, and maintaining the integrity of stored products.
6. Instrument Air:
Instrument air is essential for operating pneumatic instruments, analyzers, and control devices throughout the petrochemical plant. Air compressors supply compressed air that is treated and conditioned to meet the stringent requirements of instrument air quality standards. Instrument air is used for tasks such as pneumatic conveying, pneumatic actuators, and calibration of instruments.
By employing air compressors in the petrochemical industry, operators can ensure reliable and efficient operation of pneumatic systems, power various tools and equipment, support critical processes, and maintain safe and controlled environments.
.webp)
Can air compressors be integrated into automated systems?
Yes, air compressors can be integrated into automated systems, providing a reliable and versatile source of compressed air for various applications. Here’s a detailed explanation of how air compressors can be integrated into automated systems:
Pneumatic Automation:
Air compressors are commonly used in pneumatic automation systems, where compressed air is utilized to power and control automated machinery and equipment. Pneumatic systems rely on the controlled release of compressed air to generate linear or rotational motion, actuating valves, cylinders, and other pneumatic components. By integrating an air compressor into the system, a continuous supply of compressed air is available to power the automation process.
Control and Regulation:
In automated systems, air compressors are often connected to a control and regulation system to manage the compressed air supply. This system includes components such as pressure regulators, valves, and sensors to monitor and adjust the air pressure, flow, and distribution. The control system ensures that the air compressor operates within the desired parameters and provides the appropriate amount of compressed air to different parts of the automated system as needed.
Sequential Operations:
Integration of air compressors into automated systems enables sequential operations to be carried out efficiently. Compressed air can be used to control the timing and sequencing of different pneumatic components, ensuring that the automated system performs tasks in the desired order and with precise timing. This is particularly useful in manufacturing and assembly processes where precise coordination of pneumatic actuators is required.
Energy Efficiency:
Air compressors can contribute to energy-efficient automation systems. By incorporating energy-saving features such as Variable Speed Drive (VSD) technology, air compressors can adjust their power output according to the demand, reducing energy consumption during periods of low activity. Additionally, efficient control and regulation systems help optimize the use of compressed air, minimizing waste and improving overall energy efficiency.
Monitoring and Diagnostics:
Integration of air compressors into automated systems often includes monitoring and diagnostic capabilities. Sensors and monitoring devices can be installed to collect data on parameters such as air pressure, temperature, and system performance. This information can be used for real-time monitoring, preventive maintenance, and troubleshooting, ensuring the reliable operation of the automated system.
When integrating air compressors into automated systems, it is crucial to consider factors such as the specific requirements of the automation process, the desired air pressure and volume, and the compatibility of the compressor with the control and regulation system. Consulting with experts in automation and compressed air systems can help in designing an efficient and reliable integration.
In summary, air compressors can be seamlessly integrated into automated systems, providing the necessary compressed air to power and control pneumatic components, enabling sequential operations, and contributing to energy-efficient automation processes.
.webp)
How is air pressure measured in air compressors?
Air pressure in air compressors is typically measured using one of two common units: pounds per square inch (PSI) or bar. Here’s a brief explanation of how air pressure is measured in air compressors:
1. Pounds per Square Inch (PSI): PSI is the most widely used unit of pressure measurement in air compressors, especially in North America. It represents the force exerted by one pound of force over an area of one square inch. Air pressure gauges on air compressors often display pressure readings in PSI, allowing users to monitor and adjust the pressure accordingly.
2. Bar: Bar is another unit of pressure commonly used in air compressors, particularly in Europe and many other parts of the world. It is a metric unit of pressure equal to 100,000 pascals (Pa). Air compressors may have pressure gauges that display readings in bar, providing an alternative measurement option for users in those regions.
To measure air pressure in an air compressor, a pressure gauge is typically installed on the compressor’s outlet or receiver tank. The gauge is designed to measure the force exerted by the compressed air and display the reading in the specified unit, such as PSI or bar.
It’s important to note that the air pressure indicated on the gauge represents the pressure at a specific point in the air compressor system, typically at the outlet or tank. The actual pressure experienced at the point of use may vary due to factors such as pressure drop in the air lines or restrictions caused by fittings and tools.
When using an air compressor, it is essential to set the pressure to the appropriate level required for the specific application. Different tools and equipment have different pressure requirements, and exceeding the recommended pressure can lead to damage or unsafe operation. Most air compressors allow users to adjust the pressure output using a pressure regulator or similar control mechanism.
Regular monitoring of the air pressure in an air compressor is crucial to ensure optimal performance, efficiency, and safe operation. By understanding the units of measurement and using pressure gauges appropriately, users can maintain the desired air pressure levels in their air compressor systems.
editor by CX 2023-11-09